1. 如果紙板水分過高，預熱輥溫度達不到要求，須增加鍋爐蒸汽壓力，使之供出的蒸汽達到飽和蒸汽，一般情況下蒸汽壓力應該保持在1.1Mpa±0.2Mpa。
1. If the moisture content of the paperboard is too high and the temperature of the preheating roller cannot meet the requirements, the boiler steam pressure must be increased to make the steam supplied reach saturated steam. Generally, the steam pressure should be maintained at 1.1MPa ± 0.2MPa.
2. 如果水分偏低，就要調節導紙輥，減少預熱面積，同時要充分利用單面機上噴霧裝置（濕潤輥），對原紙進行噴霧，增加原紙水分，使之達到標準要求。
2. if the moisture is low, adjust the guide roll and reduce the preheating area. At the same time, we should make full use of the spray device on the single plane (Shi Rungun) to spray the base paper and increase the moisture content of the base paper, so as to meet the standard requirements.
3. 平板烘缸在工作時，不到萬不得已時，不能停車。單面機要更換原紙前應提速，在橋架上增加堆積量；復合機在接到信號后應降速，待單面機完成接紙后，再行提速。若設備發生故障等必須停車時，應將輸送帶提升，以防停留在平板烘缸上紙板水分過度流失。
3. When the flat dryer is working, it cannot stop until it is absolutely necessary. Speed up the single-sided machine before replacing the base paper and increase the stacking amount on the bridge; After receiving the signal, the speed of the compound machine shall be reduced, and the speed shall be increased after the paper receiving of the single-sided machine is completed. If the equipment fails and must be stopped, the conveyor belt shall be lifted to prevent excessive loss of paperboard moisture staying on the flat dryer.
4. 對于單面機而言，要調節好上膠輥與刮膠輥的間隙。一般情況下，上膠輥與刮膠輥的間隙為0.2mm一0.25mm，涂膠輥與主瓦楞輥在熱機狀態下的間隙應比所用瓦楞紙的厚度大0.02mm。
4. For the single-sided machine, the gap between the upper rubber roller and the rubber scraping roller shall be adjusted. In general, the gap between the upper rubber roller and the rubber scraping roller is 0.2mm-0.25mm, and the gap between the rubber coating roller and the main corrugating roller under hot engine state shall be 0.02mm greater than the thickness of the corrugated paper used.
對于雙面機而言，刮膠輥和上膠輥的間隙也為0.2mm一0.25mm，壓輥與上膠輥之間間隙應比所通過的單面瓦楞紙板高度小0.05mm一0.1mm，且兩輥兩端間隙應保持一致，可用塞尺測量。
For the double-sided machine, the gap between the rubber scraping roller and the rubber feeding roller is also 0.2mm-0.25mm. The gap between the pressing roller and the rubber feeding roller shall be 0.05mm-0.1mm smaller than the height of the single-sided corrugated board passed, and the gap at both ends of the two rollers shall be consistent, which can be measured with a feeler gauge.
為了有效控制溫度，在瓦楞紙板生產線上，很多地方都設置了加熱器和烘干板。通常情況下，車速在100m/min以上的瓦楞紙生產線，糊液的固化溫度應為160℃～180℃。如果采用蒸汽加熱方式，則要求鍋爐飽和水蒸汽的壓力應達到0.9MPa～1.4 MPa。而瓦楞紙生產線上對瓦楞紙板含水量影響比較大的設備主要是單面機組和烘干機組。針對不同情況，應該隨時對這些部分做出相應的調整，以便生產的順利進行。
In order to effectively control the temperature, heaters and drying boards are set up in many places on the corrugated board production line. Generally, the curing temperature of the paste solution of the corrugated paper production line with a speed of more than 100m / min shall be 160 ℃ ~ 180 ℃. If steam heating is adopted, the pressure of saturated steam of boiler shall reach 0.9mpa ~ 1.4mpa. The main equipment on the corrugated paper production line that has a great impact on the water content of corrugated board are single-sided unit and drying unit. According to different situations, these parts should be adjusted at any time to facilitate the smooth progress of production.
Good products make good services, and good manufacturers make good works. Corrugated box manufacturers insist on providing customers with high-quality services. Please continue to pay attention to our website for details: http://m.ywjbs.com
